mirror of
https://bitbucket.org/myhomie/mycorerepository.git
synced 2025-12-06 17:51:20 +00:00
88 lines
3.1 KiB
C++
88 lines
3.1 KiB
C++
#include "IRremote.h"
|
|
#include "IRremoteInt.h"
|
|
|
|
//+=============================================================================
|
|
void IRsend::sendRaw (const unsigned int buf[], unsigned int len, unsigned int hz)
|
|
{
|
|
// Set IR carrier frequency
|
|
enableIROut(hz);
|
|
|
|
for (unsigned int i = 0; i < len; i++) {
|
|
if (i & 1) space(buf[i]) ;
|
|
else mark (buf[i]) ;
|
|
}
|
|
|
|
space(0); // Always end with the LED off
|
|
}
|
|
|
|
//+=============================================================================
|
|
// Sends an IR mark for the specified number of microseconds.
|
|
// The mark output is modulated at the PWM frequency.
|
|
//
|
|
void IRsend::mark (unsigned int time)
|
|
{
|
|
TIMER_ENABLE_PWM; // Enable pin 3 PWM output
|
|
if (time > 0) custom_delay_usec(time);
|
|
}
|
|
|
|
//+=============================================================================
|
|
// Leave pin off for time (given in microseconds)
|
|
// Sends an IR space for the specified number of microseconds.
|
|
// A space is no output, so the PWM output is disabled.
|
|
//
|
|
void IRsend::space (unsigned int time)
|
|
{
|
|
TIMER_DISABLE_PWM; // Disable pin 3 PWM output
|
|
if (time > 0) IRsend::custom_delay_usec(time);
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
//+=============================================================================
|
|
// Enables IR output. The khz value controls the modulation frequency in kilohertz.
|
|
// The IR output will be on pin 3 (OC2B).
|
|
// This routine is designed for 36-40KHz; if you use it for other values, it's up to you
|
|
// to make sure it gives reasonable results. (Watch out for overflow / underflow / rounding.)
|
|
// TIMER2 is used in phase-correct PWM mode, with OCR2A controlling the frequency and OCR2B
|
|
// controlling the duty cycle.
|
|
// There is no prescaling, so the output frequency is 16MHz / (2 * OCR2A)
|
|
// To turn the output on and off, we leave the PWM running, but connect and disconnect the output pin.
|
|
// A few hours staring at the ATmega documentation and this will all make sense.
|
|
// See my Secrets of Arduino PWM at http://arcfn.com/2009/07/secrets-of-arduino-pwm.html for details.
|
|
//
|
|
void IRsend::enableIROut (int khz)
|
|
{
|
|
// Disable the Timer2 Interrupt (which is used for receiving IR)
|
|
TIMER_DISABLE_INTR; //Timer2 Overflow Interrupt
|
|
|
|
pinMode(TIMER_PWM_PIN, OUTPUT);
|
|
digitalWrite(TIMER_PWM_PIN, LOW); // When not sending PWM, we want it low
|
|
|
|
// COM2A = 00: disconnect OC2A
|
|
// COM2B = 00: disconnect OC2B; to send signal set to 10: OC2B non-inverted
|
|
// WGM2 = 101: phase-correct PWM with OCRA as top
|
|
// CS2 = 000: no prescaling
|
|
// The top value for the timer. The modulation frequency will be SYSCLOCK / 2 / OCR2A.
|
|
TIMER_CONFIG_KHZ(khz);
|
|
}
|
|
|
|
//+=============================================================================
|
|
// Custom delay function that circumvents Arduino's delayMicroseconds limit
|
|
|
|
void IRsend::custom_delay_usec(unsigned long uSecs) {
|
|
if (uSecs > 4) {
|
|
unsigned long start = micros();
|
|
unsigned long endMicros = start + uSecs - 4;
|
|
if (endMicros < start) { // Check if overflow
|
|
while ( micros() > start ) {} // wait until overflow
|
|
}
|
|
while ( micros() < endMicros ) {} // normal wait
|
|
}
|
|
//else {
|
|
// __asm__("nop\n\t"); // must have or compiler optimizes out
|
|
//}
|
|
}
|
|
|